Results 1 to 30 of 30

Thread: Who do you use? - Dynotuning, Sydney

  1. #1

    Who do you use? - Dynotuning, Sydney

    Hey All,
    I just put a PCV on my 06 CBR1000RR and wanted to see what the general consensus was on who`s the best for tuning in the Sydney area (Preferably Western Sydney). Im not after all out power but smooth and reliable performance.
    Thanks in advance.
    Cheers,
    Chris

  2. #2
    check out Trevor at Doin Bikes, Moorebank way / Chipping Norton

  3. #3
    Moderator Baddie's Avatar
    Join Date
    Feb 2013
    Location
    Glenmore Park
    Posts
    352
    Welcome Chris...

    Good to see to you joined...like I mentioned on the Winners site..I had my girlfriend done by Brad at Bikebiz, and very happy so far.


  4. #4
    I have an 05 CBR1000RR and have some really good maps for yoshi slip on and bmc filter,send me your email and i'll get them to you.Steve. AT the creek tomorrow so prob won't be until Monday.0421526521

  5. #5
    Mine are being done by Road and Circuit at the moment. Very good work - thorough rather than cheap.
    IMA Thumb Brakes! Shop now

    Annitori QS PRO quickshifters Shop now

    Superbike Source Racing: 'Like' our page to keep up-to-date with all our racing


  6. #6
    Thanks for the quick responses guys I'll check those places out. Steve, I've sent you a PM

  7. #7
    If you want to try some today and get a break in the weather go to 1000RR there is a thread on maps and try Jims map (Resusit8 ?) I used it for a couple of years ,great map with - 1 front sprocket and r6 throttle tube. i'll give more of a list Monday

  8. #8
    Thanks Steve, I'm not in any rush and can't ride for a few weeks yet, I'm recovering from a fractured hand and some tendon damage, I checked yesterday to see if I could pull the clutch lever but still no good....:(

  9. #9
    I initially got Motologic to Dyno tune my 1199S when they fit the full Termi system and a Rapid Bike ECU. They got a respectable 174hp at the rear wheel.

    Then I used TuneBoy in Hornsby to do it all again. First thing he did was removed the Rapid Bike ECU. I'm not technical but I believe he re-flashed the "perfectly capable" factory ECU and custom tuned it. He got it to 192hp at the rear wheel with more power and torque right throughout the rev range. He even included cruise control. Total cost $600 or what I paid for the Rapid Bike ECU alone....

    Cost is less for smaller capacity / simpler bikes I believe.


    Sent from my iPhone using Tapatalk

  10. #10
    Quote Originally Posted by Spilly1199 View Post
    I initially got Motologic to Dyno tune my 1199S when they fit the full Termi system and a Rapid Bike ECU. They got a respectable 174hp at the rear wheel.

    Then I used TuneBoy in Hornsby to do it all again. First thing he did was removed the Rapid Bike ECU. I'm not technical but I believe he re-flashed the "perfectly capable" factory ECU and custom tuned it. He got it to 192hp at the rear wheel with more power and torque right throughout the rev range. He even included cruise control. Total cost $600 or what I paid for the Rapid Bike ECU alone....

    Cost is less for smaller capacity / simpler bikes I believe.


    Sent from my iPhone using Tapatalk
    Thanks, I'll check them out too.

  11. #11
    Has anyone had any experience with S&R Pro at Penrith?

  12. #12
    Mototech Australia in Smithfield are good


    Sent from my iPhone using Tapatalk

  13. #13
    Hang on.... this says 'Flywheel Power', not RWHP. Are they doing a 'correction' to get a higher number? It sure looks like it.

    And I've gotta laugh, because your graph starts higher than mine tops out at!!

    Quote Originally Posted by Spilly1199 View Post
    I initially got Motologic to Dyno tune my 1199S when they fit the full Termi system and a Rapid Bike ECU. They got a respectable 174hp at the rear wheel.

    Then I used TuneBoy in Hornsby to do it all again. First thing he did was removed the Rapid Bike ECU. I'm not technical but I believe he re-flashed the "perfectly capable" factory ECU and custom tuned it. He got it to 192hp at the rear wheel with more power and torque right throughout the rev range. He even included cruise control. Total cost $600 or what I paid for the Rapid Bike ECU alone....

    Cost is less for smaller capacity / simpler bikes I believe.


    Sent from my iPhone using Tapatalk
    IMA Thumb Brakes! Shop now

    Annitori QS PRO quickshifters Shop now

    Superbike Source Racing: 'Like' our page to keep up-to-date with all our racing


  14. #14
    Quote Originally Posted by Ausgecko View Post
    Has anyone had any experience with S&R Pro at Penrith?
    Funny you mention Sand R pro. I Turbo'ed the CBR and Jamie at S&R did the tuning work on it after a blown motor elsewhere and he is the only guy I would now let near the thing.As for normally aspirated I haven't had him do any work but he definitely knows his stuff and has the runs on the board in drag racing circles on his own bikes .Him an Rupert are nice guys too.

  15. #15

    Who do you use? - Dynotuning, Sydney

    Quote Originally Posted by stevem View Post
    Funny you mention Sand R pro. I Turbo'ed the CBR and Jamie at S&R did the tuning work on it after a blown motor elsewhere and he is the only guy I would now let near the thing.As for normally aspirated I haven't had him do any work but he definitely knows his stuff and has the runs on the board in drag racing circles on his own bikes .Him an Rupert are nice guys too.
    Ok, cool. I had him do some work and was very happy with the service so I was going to get him to tune it but when I asked him about it he quoted me a price and said that it was because he had to do something with the ECU also, the price wasn't a problem but when I asked him about the ECU he kind of brushed it off a bit and didn't seem to want to tell me what he has to do and I thought that was odd. After some research I've found out that at most he will need to "tap into" it to get an RPM readout but that's it, he made it sound like it was more than that and it kind of threw me.
    He's just around the corner from me so it's very convenient, I'm just trying to get some peace of mind of where I should send it, I've heard some bad stories about some places but none of S&R.

    I guess I'm just fishing for info

  16. #16
    I have sent you 2 emails .RESUS map I have run on the road for 2 years no worries with a yoshi slip on,bmc race filters ,-1 front sprocket and an r6 throttle tube and did a 9.96 quarter mile.If it was me I would just run this,but for peace of mind get it tuned if you want.Enjoy it man what ever you do.Steve.

  17. #17
    Moderator Baddie's Avatar
    Join Date
    Feb 2013
    Location
    Glenmore Park
    Posts
    352
    "192hp at the rear wheel"...its is a ducati right???


  18. #18
    Oh, while we are posting graphs, here are my two R6s. The blue one is the stock motor, and the red one is the "YEC" one that turned out not to be.

    And I see that these are also 'power at the engine', not the rear wheel! Not sure whether that's how they all do it??

    IMA Thumb Brakes! Shop now

    Annitori QS PRO quickshifters Shop now

    Superbike Source Racing: 'Like' our page to keep up-to-date with all our racing


  19. #19
    Moderator chubb's Avatar
    Join Date
    Feb 2013
    Location
    Melbourne
    Posts
    2,032
    120 although not 136+ is still not too shabby

  20. #20
    Or 7hp+ over a stock-ish bike!!!

  21. #21
    Hey Steve,
    Thanks for the maps, your a champion!

  22. #22
    Quote Originally Posted by Ausgecko View Post
    Has anyone had any experience with S&R Pro at Penrith?
    Yeah, I have. Jamie knows his shit. Especially if you want to turbo something. I recommend him highly.

  23. #23
    Quote Originally Posted by Marshy View Post
    Hang on.... this says 'Flywheel Power', not RWHP. Are they doing a 'correction' to get a higher number? It sure looks like it.

    And I've gotta laugh, because your graph starts higher than mine tops out at!!
    Think it must be a mistake because when I had it dyno'd at eastern creek it have the 174 RW HP & the MotoLogic figures were RW as well. Plus the Pani is supposed to have 195 at the crank stock standard without pipes etc. I will ask the question though!


    Sent from my iPhone using Tapatalk

  24. #24
    Nah, mine's the same - I think it's just a field variable they enter on the form. Doesn't affect the results.
    IMA Thumb Brakes! Shop now

    Annitori QS PRO quickshifters Shop now

    Superbike Source Racing: 'Like' our page to keep up-to-date with all our racing


  25. #25
    Yea so you mean they entered the wrong data in that field?


    Sent from my iPhone using Tapatalk

  26. #26
    I mean that, eg on my map, where it says "Power at:" they selected 'Engine' instead of 'Rear Wheel'. Just a drop down field. The default is probably Engine.

    I'm guessing, but it's an educated guess

    Anyone able to clarify?
    IMA Thumb Brakes! Shop now

    Annitori QS PRO quickshifters Shop now

    Superbike Source Racing: 'Like' our page to keep up-to-date with all our racing


  27. #27
    Senior Member Marty's Avatar
    Join Date
    Jul 2013
    Location
    Western Sydney
    Posts
    401
    I use doin' bikes, had my bike mapped twice over the years with different parts. I've used off the shelf maps in other bikes before and there's no comparison

  28. #28
    Senior Member dan's Avatar
    Join Date
    Jun 2013
    Location
    Sydney
    Posts
    1,298
    What should you expect to pay for a dyno tuning? Roughly
    do a burnout

  29. #29
    $300 for a cashie on the side, easy tune (plug-in tune for a PC or Bazzaz) where it maps automatically, to $600-700 or up for a hand-done tune, custom mapped into a YEC ECU or the like (eg flashed stock ECU). My very limited experience shows that there's no real power difference between the two, but the bike will run smoother especially down low with the customised jobbie. It's more about the time spent tweaking all the numbers at all the rpm points.
    IMA Thumb Brakes! Shop now

    Annitori QS PRO quickshifters Shop now

    Superbike Source Racing: 'Like' our page to keep up-to-date with all our racing


  30. #30
    Quote Originally Posted by dan View Post
    What should you expect to pay for a dyno tuning? Roughly
    Tuneboy was $650 for the Pani including the $100 for cruise control. For a 600 looking at around $400 with no need for PC etc


    Sent from my iPhone using Tapatalk

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •