YEC ECU and Harness- R6 or R1 [Archive]

Saturnalian

24-04-2014, 12:52 PM

Yullo,

Is anyone else out there actually running a YEC ECU / Harness combination ?

I've started swapping all of the necessary sensors over to the new project chassis and going through and marking the YEC loom have noticed that they have no provisions for the thermo fans at all.
It makes sense to me that this is because race bikes don't run thermo fans ? I do find them handy both on dry hot track days and occasionally to flick the switch on the out lap when racing and let them run until everyone is gridded up.

Any thoughts / idea's on this one ?

Marshy

24-04-2014, 12:55 PM

I have the YEC ECU and race harness in both my bikes. You're right - there's no provision for fans at all! There's also no Neutral sensor, so you don't get the N light on the dash....

I hardwire in a fan switch as per my 'how-to' thread. Use the (thoughtfully provided by YEC) accessories switched power/earth source on the harness (near the dash plug). This is also perfect for a lap timer etc.

chubb

24-04-2014, 02:34 PM

dan

24-04-2014, 02:55 PM

better stop Jamie you'll take the clubsport by storm!

Fucking aye this thing is going to be a serious bit of kit.

Tristan

24-04-2014, 03:06 PM

You should probably get an R6 too Dan like seriously it's only money don't be gay hahaha

Sent from my iPhone using Tapatalk

Mstevo

24-04-2014, 03:25 PM

better stop Jamie you'll take the clubsport by storm!
1/2 the fun is building it, the other half is racing it :-)

dan

24-04-2014, 03:37 PM

You should probably get an R6 too Dan like seriously it's only money don't be gay hahaha

Sent from my iPhone using Tapatalk

one day, for now i've got to give you guys a chance though ;)

chubb

24-04-2014, 04:13 PM

1/2 the fun is building it, the other half is racing it :-)

I'm almost done with the fibreglassing... jeez it takes a long time sanding...

dan

24-04-2014, 04:40 PM

I'm almost done with the fibreglassing... jeez it takes a long time sanding...

I decided I'm just going to pull the stickers off mine and give it a bunch of coats without even sanding it haha

Mr.Ed

24-04-2014, 04:44 PM

If you don't sand it, you'll have a bad time

dan

25-04-2014, 02:59 PM

Not even fussed

Mr.Ed

25-04-2014, 04:19 PM

The paint will run... that's the @#$ part of it. Trust me. I've done the lazy work before... lol

dan

25-04-2014, 07:15 PM

It's not and show and shine. I'd rather spend time and money on going fast.

dan

25-04-2014, 07:22 PM

Also trying to race prep an aprilia 125, a cb bucket, a dirt track smoker and a spare gsxr600. Nice paint job on fairings is so irrelevant in the scheme of things.

Mr.Ed

25-04-2014, 07:23 PM

Not judging... and if you ever saw any of my bikes you'd know I agree. But you'll waste your paint by using it without at least a mild prep... might as well save the money and time and just bring the battle scars to the track. I know I did and never regretted it. Well... when ppl point and laugh as you ride by it can get to you if you're feeling vulnerable on that particular day. Not that it ever happened to me or anything...

Marshy

25-04-2014, 10:18 PM

Well... when ppl point and laugh as you ride by it can get to you if you're feeling vulnerable on that particular day. Not that it ever happened to me or anything...

:rofl: Sorry Ed; I didn't mean to laugh.... ;)

Mr.Ed

25-04-2014, 11:55 PM

hahaha it's the pointing that hurts...

Marty

26-04-2014, 08:12 AM

When I did top rider I saw Ant West looking over my bike and laughing at shit. Prick!

chubb

26-04-2014, 08:27 AM

Look at Michael Jeffrey.

Quick rider ordinary paint job.

dan

26-04-2014, 10:30 AM

Might lay some $2 primer down before I hit it with the old export rattle can haha

dan

26-04-2014, 10:30 AM

When I did top rider I saw Ant West looking over my bike and laughing at shit. Prick!

Haha awesome

chubb

21-07-2014, 03:31 PM

Again back on topic.

Is there no triangle speed sensor on the YEC harness either??

Trying to find out if the bazzaz can run without Speed and neutral sensor.

Saturnalian

21-07-2014, 05:32 PM

The YEC harness has no speed sensor, no neutral light and no fan allowance.

Sent from my iPhone using Tapatalk

chubb

21-07-2014, 05:47 PM

what about the 4 pin coupler at the front .. there's a speed wire there..

Saturnalian

21-07-2014, 08:10 PM

what about the 4 pin coupler at the front .. there's a speed wire there..

Yes it does. I don;'t know why this is causing some short circuiting in my brain.
If i remember whatever it is about that little wire i'll come back to you....

chubb

21-07-2014, 08:16 PM

I think I'll just have to live without neutral...

Marshy

22-07-2014, 09:05 AM

Yes it does. I don;'t know why this is causing some short circuiting in my brain.

Me too! I'd forgotten that also. but I know I had a gear indicator wired in to a YEC harness, so it's certainly possible (and I don't recall it being hard). I never had a neutral light though. It's pretty easy to do without, although if you were keen, the sensor off the gearbox is still physically there, and the light on the dash is too, so it probably isn't technically too difficult to bodgy up a connection.

chubb

22-07-2014, 09:22 AM

Nah I can live without neutral.. just want the gear indicator on the dash to work..

Marshy

22-07-2014, 09:54 AM

Same then. Just grab the signal from the sensor.

Saturnalian

22-07-2014, 09:22 PM

Oh, I have my Gipro working still on the YEC harness. I can help you with that. Or is your ECU re flashed so it shows gear on the stock dash

Sent from my iPhone using Tapatalk

Carl-52

22-07-2014, 10:05 PM

hes got a Hm dash

chubb

23-07-2014, 07:14 AM

you got a netural sensor hooked up Jamie?

chubb

23-07-2014, 07:16 AM

Oh, I have my Gipro working still on the YEC harness. I can help you with that. Or is your ECU re flashed so it shows gear on the stock dash

Sent from my iPhone using Tapatalk

I got one with reflashed ECU

one with YEC ECU

Stock dash is just backup for clearing error codes and in case the HM fails. (touch wood)