PDA

View Full Version : 2016 Aprilia RSV4 RF



ironside
24-10-2016, 08:27 PM
Look what I picked up at the weekend!

1883

Marshy
25-10-2016, 05:47 AM
Oh my gosh!!! That's beautiful!! Ask away for setup tips.


Sent from my iPhone using Tapatalk

Turbo
26-10-2016, 08:29 PM
I think I'm most impressed with the van light... It's like a wee showroom in there! :lol:

Nice pickup, Simon. What's the scoop? '96 Gixxer? for road use only? :P

Kris
28-10-2016, 08:28 AM
Nice one, enjoy!

ironside
28-10-2016, 07:40 PM
Cheers guys :)


I think I'm most impressed with the van light... It's like a wee showroom in there! :lol:

Actually the van was awesome. New Transit and I think the first time they've put something other than the interior light out of a Ford Orion in the load area. It had tons of LEDs instead, brilliant!

Haven't changed a thing on the bike yet, it's brand new so am running it in on the road first. I'm about halfway to the 1km first service, should finish it this weekend.

ironside
27-01-2017, 04:28 AM
Been awhile since I updated this. . .
I've run it in on the road for the required 1000km up to 7500rpm, serviced and then another 1000km up to 9500rpm. After that it was time to start the conversion for track.

First thing's first - GiaMoto rearsets:
1905 1908

These are lovely; race shift items that still use the original quickshifter sensor. They even have folding tips on the brake and gear shift levers.
Taking the standard footrests off was a doddle, I'm impressed with how simple the Aprilia is to work on compared to the Hondas I've had before. Things come off in complete assemblies with just a couple of bolts instead of having to remove lots of individual pieces.

Nice improvement, I think:
1907 1909

Turbo
27-01-2017, 07:06 PM
Very neat bit of kit there! Machining looks amazing. Love the wee Italian flag too!
What's next??!!

ironside
27-01-2017, 09:56 PM
Well no track bike build is complete without some GB Racing stuff:

1910 1911 1912 1913

Nice to see the RSV4 actually already has paddock stand bobbins, chain toe guard etc.

I'm still undecided on whether or not to fit the bullet sliders. Fitted, they sit flush with the fairing (by cutting in to them) about where the little stand offs are where the fairings are bolted on.
I'm fitting track fairings, so I don't mind cutting them, and they'd obviously beef up the (intenionally?) weak stand offs. I'm just unsure if they'll actually do any good having been stung before by flipping a bike on R&G bungs.

Turbo
28-01-2017, 08:23 PM
I'm in two minds about crash protection too. I think it largely depends on the bike and whether the transferal of force will do harm or good.
Or whether it'll get caught on something and ultimately flip the bike, in what would have been a smooth slide...?

Mr.Ed
28-01-2017, 08:39 PM
I like the Woodcraft ones that are almost flush with the farings... they stick like 2-3cm out. Enough to protect but less likely to dig in

Turbo
28-01-2017, 08:49 PM
I like the Woodcraft ones that are almost flush with the farings... they stick like 2-3cm out. Enough to protect but less likely to dig in

Agreed, I like them on the R6. Never had any frame damage or dug in to flip it. Are you thinking Kwaka?
I've seen people snap frames on the BMW tho, as it's a pretty thin part of the frame they fit too, so I don't run them anymore.

Mr.Ed
28-01-2017, 09:00 PM
I had the longer version and it cracked an engine mount on mine on a 25kmh crash... also cracked my collarbone on that one but that's another story lol. The shorty would have been fine I think as the long one dug into the gravel trap

Turbo
28-01-2017, 09:13 PM
... also cracked my collarbone on that one but that's another story lol.

Well I think you shouldn't really have attached it to your collarbone... They're simply not designed for that sort of application.

Mr.Ed
28-01-2017, 09:24 PM
It didn't say not to do it in the instructions and I've been told I have a chip on my shoulder so...

Marshy
30-01-2017, 07:25 AM
Bahahhahaa!

I don't run them on any bike anymore. It's not worth the risk. The aprilias are very narrow anyway, and frame damage is very unlikely in a slide. Fairings etc are a consumable, and replacing them is preferable to fixing a cartwheeled bike ;)

ironside
30-01-2017, 11:16 PM
I'm inclined to agree, especially as it suits my laziness . . .

Talking of fairings, these exciting looking boxes arrived from Sebimoto (http://www.sebimoto.com/):

1918 1917

I bought pretty much everything they sell for the RSV4 RF. Front fairing, air tubes, belly pan, tail/seat unit, front mudguard, rear hugger, frame & swingarm protectors and a fuel tank cover.
The fuel tank cover hasn't actually arrived yet and I've since discovered that the factory one isn't a tank cover (like they are on a Honda), that's the actual tank - made of plastic?!
So I have a decision to make; whether to paint the tank I have, try and find a used one to paint or fit the Sebimoto cover and hope it doesn't batter the factory finish underneath too badly.

Full marks to Sebimoto for the fit and finish of their fairings. I didn't need to fettle anything to get it to fit except drill holes (including some holes in the side fairing to re-home the regulator/rectifier and the V4 Mobile Platform gizmo).
The only "modifications" I made was some foil tape inside the belly pan to help with exhaust heat and some 10mm seat foam. Screen is still the factory one for the time being.

1920 1919 1921

Marshy
31-01-2017, 06:40 AM
that's the actual tank - made of plastic?!

Yep, plastic tank, which is a FANTASTIC idea because they don't dent in a crash! They are very hard-wearing in a slide, too, although I still add c/f sliders.


So I have a decision to make; whether to paint the tank I have, try and find a used one to paint or fit the Sebimoto cover and hope it doesn't batter the factory finish underneath too badly.


I smother the oem tank in electrical tape before putting the cover on. It will wear through in spots over time, but it's fairly good protection in the medium term, particularly with sliders on the corners of the tank, which keeps the cover from scratching the tank at the most vulnerable spots.

ironside
31-01-2017, 08:16 AM
I smother the oem tank in electrical tape before putting the cover on. It will wear through in spots over time, but it's fairly good protection in the medium term, particularly with sliders on the corners of the tank, which keeps the cover from scratching the tank at the most vulnerable spots.

Didn't think of that - great idea! I'll wait for the cover to come and see how well it fits before deciding then.